■ Fits Konica Minolta Battery model:
Dimage X50, Dimage X60
DG-X50-K, DG-X50-R, DG-X50-S
■ Package includes
1x Charger
1x Compact Universal Adapter,
1x User Manual.
1x Car Cigarette Lighter Jack Adapter (Optional)
■ Voltage In : 100-240V ( Universal )
■ Charging voltage limit: 4.2V max
■ Charging current limit: 650mA max
■ For batteries rated: 3.6V - 3.7V average
■ Dimension : 106.50 x 69.00 x 33.50 mm
■ Weight: 220.00(g)
■ Color : Silver
Q: Why is the battery 3.7V and the charger outputs 4.2V?
A: The charger is limited at 4.2V, but does not go to 4.2V immediately when the battery is just plugged in. It first charges the battery at a constant current until the voltage reaches 4.2V. Then, it stays at 4.2V for a few minutes. Then it shuts off and the LED turns green. This is according to Li-Ion charging specifications (optimal voltage is 4.2V, nominal at 3.7V). It is different from Ni-MH or Ni-Cd battery charging. Read our Forum for battery charging tips.
Q: Why would the LED turn red and immediately turn green with my battery?
A: Your battery is "dead". It has lost over 90% of its capacity. This usually happens when you overdischarge the battery too much. Read out Forum for battery usabe tips. You need to get a new battery.
Q: The LED never turns red but my battery works. Is the charger bad?
A: There is a chance the battery terminals do not touch the charger contacts all the way or became dirty. Please, check that. If necessary clean the battery terminals or slightly bend the charger contacts to have a better connection. If this is not the case - then yes, the charger is bad. Generally, these chargers have a very low rate of returns. Less than one in 500.
Battery Charger Description
The AVMP charger is for video camcorder and digital camera Li-ion batteries. It is suitable for different battery models to use,only to change the plate which is located on the top of the charger.
(A) How to change the charger plate
Part I : Release the charger plate |
Step 1:
Press the buttons, located on the bottom of the charger.
|
Step 2:
Charger plate release from the base.
|
Step 3:
Took out the plate.
|
|
|
Part II : Install the new charger plate |
Step 1:
Ready a new charger plate.
|
Step 2:
Install the front into the charger base and press the end down to the base.
|
Step 3:
Complete the installation.
|
|
(B) Charging method
Our Battery Charger have two charging method: AC Adapter and Car cord, They allow you to charge your battery at home or in the car conveniently.
Method 1:
Power by AC Power Adapter
|
Method 2:
Power by DC Car Cord
|
|
(C) Check the charging status
The LED indicator will show for you the charging status.
|
|
|
Here are the steps for using the charger
1. |
Plug the AC Adapter into the wall outlet or the DC car cord to the automobile cigarette socket. |
2. |
Connect the AC Adapter or car cord to the charger DC in-jack. |
3. |
"Status" LED indicator show RED when the Charger is ready and "Charge" LED indicator show flashing GREEN when waiting for battery pack. |
4. |
Slide battery pack into the charger and "Charge" LED indicator turns RED when charging. |
5. |
"Charge" indicator flashes RED and GREEN alternatively when battery pack has been charged over 90%. |
6. |
When the battery pack is fully charged, the "Charge" LED indicator turns steady GREEN. |
7. |
After the battery pack fully charged, slide the battery pack out and unplug power. |